Chilled Tech - LED Grow Lights & Spectrum Control
Commercial & DIY LED grow lights - Highest efficiency, power & quality - Made in USA
Thin Profile – Only 1.375in Tall
Oversized surface area for maximum heat dissipation
Lower your heat load by removing power driver outside grow area
Made in the USA – Finest quality materials and workmanship
Input Power Draw: 1000W
Input Voltage Range: 90-305 VAC
120 VAC Current Draw: 8.4 Amps
208 VAC Current Draw: 4.8 Amps
240 VAC Current Draw: 4.2 Amps
277 VAC Current Draw: 3.6 Amps
Power Drivers: 2 x Mean Well HLG-480H-48B
AC Power Cord Length: 6.5 ft
DC Extension Cord Length: 7 ft
Dimming Range: 5-100%
Light Engine Efficacy: 3.26 μmole/J – 2.73 μmole/J
Power Driver Efficiency: 95% @ 230 VAC
Full System Efficacy: 3.08 μmole/J – 2.58 μmole/J
Light Bar LED Information:
Samsung 3000K White LEDs – 140 per Light Bar
Samsung 5000K White LEDs – 140 per Light Bar
660nm Deep Red LEDs – 15 per Light Bar
Warranty: 3-Year DIY Kits Warranty Included
Operating Temperature Range: 41°F – 95°F | 5°C – 35°C
Operating Humidity Range: 10 – 90% Non-Condensing
Generated Heat Load: 3,412 BTU/Hour
Water Protection: Currently the Growcraft has no protective coating against direct moisture exposure. If moisture accumulates near the LEDs damage may occur. Make sure to point any sprays downward and away from the LEDs.
Use of VOC (Volatile Organic Compounds): DO NOT USE VOCs, like burning sulfur, near any Growcraft. This can damage the LEDs beyond repair and is NOT covered by our warranty.
Minimum Head Space Above Fixture: 10 in
Recommended Hanging Height: 18-30 in
Recommended Grow Room Ambient Air Temperature: 85°F | 29.5°C
Coverage Area: 5 x 5 ft
Start Slow – Growcraft lights have VERY high light output and unless your plants are already acclimated to high light intensity, it is best to start slow with the light hanging high and possibly also dimmed. Then monitor plant reaction over a few days and slowly adjust as needed.
Fixture Dimensions: 42.5 in x 42.5 in x 1.375 in
Fixture Weight: 33.85 Lbs
2 x Growcraft DIY U-Frame – 4×4
2 x Growcraft DIY U-Frame Cover – 4×4
2 x Growcraft Power Distribution PCB – 2×4
6 x Growcraft 40in Heatsink
6 x Growcraft 40in LED Board
1 x M3 – 6mm Plastite PCB Screw – 5 pack
1 x M3 – 8mm Plastite PCB Screw – 25 pack
1 x M3 – 5mm Countersunk Torx Screw – 25 pack
1 x M4 – 14mm Torx Screw – 25 pack
6 x Growcraft PCB End Cover 2 Pack – ChilLED WHITE
2 x Growcraft Strain Relief Cable Gland – Black
1 x 20 AWG Red & Black Solid Core Wire Pair – 6ft
2 x Push Lock 7ft Driver Extension Cable
2 x Push Lock AC Power Cord (Your Choice of AC Plug)
2 x Push-Lock Mean Well HLG-480H-48B LED Driver
1 x Push-Lock Dimmer Pot
1 x Growcraft DIY U-Frame Hole Plug
4 x Rope Ratchets
1 x T10 & T20 Torx Bit Pack
| Weight | 51.45 lbs |
|---|---|
| Dimensions | 43.45 × 8.95 × 7.7 in |
| LED Spectrum | Flowering Optimized/Full Cycle Spectrum, Vegetative Cycle Optimized Spectrum |
| AC Power Plug | USA 120V (Standard), USA 240V, EU Plug, Australia & New Zealand |
Erwin (verified owner) –
By far the best lights ive ever use and ive used several different brands. Very easy to put together after i looked at there youtube video.the support team is always helpful and pretty fast in returning any answers to any questions i have, thanks by the way. Lights are very sturdy and very bright, you definitely need protective glasses is your using these awsome lights.
Gabrielle –
Erwin, thanks for taking the time to let us know of your experience with the setup of the grow light and customer service. We are always here for our growers! 🙂
Aaron Bomaster (verified owner) –
The light is easy to build stays very cool compared to all other lights I’ve used. It’s light intensity is amazing and the canopy penetration is amazing
Gabrielle –
The ChilLED team is so pleased to hear this! Thanks for taking the time out to share that with us 🙂
Maziar (verified owner) –
Best grow light I seen before, very easy to set up and thanks to the support for always replying back to any questions, this is the Ferrari in grow lights.
Gabrielle –
Thank you for taking the time out to share that with us ! Hope you enjoy your setup.